Other Cure

SDI Ez-Glow is a dry-bright acrylic floor polish that can be diluted with water and applied a mop to interior, sealed concrete floors. The application of EZ-Glow periodically will enhance the sheen of most sealers over interior concrete floors and also dramatically improve most sealers life spans by acting as a non-yellowing, water-resistant, shiny, tough wearing surface that is easily maintained. EZ-Glow  is diluted with 3 parts water to 1 part EZ-Glow and spray buffed, or mopped onto the sealed surface with a clean yard mop. Multiple coats are recommended for initial application followed by an occasional maintenance coat when necessary. EZ-Glow normally dries within 30 minutes. EZ-Glow comes in 1 gallon bottles concentrated. One gallon of EZ-Glow after dilution should cover approximately 300 square feet per gallon.

SDI EZ-Glow Plus is a high solids acrylic floor polish that can be burnished with high speed burnishing equipment or applied with a clean yarn mop or lambs wool applicator. EZ-Glow plus yields all the same benefits as EZ-Glow with the added bonuses of slip resistance, higher solids-content, better wear-resistance, sheen, and durability when burnished. EZ-Glow Plus does not need to be diluted. It comes in 1 gallon bottles ready-to-use. One gallon of EZ-Glow Plus can cover approximataly 1500 square feet

SDI Repel 75 is a 7.5% active, water-based siloxane/silane water repellant and impregnating agent for vertical or horizontal porous masonry surfaces such as concrete, block, brick, and unglazed tile. Repel 75 will penetrate and chemically bond deep within the substrate to provide long lasting protecting against deterioration or staining due to water conditions. Repel 75 will not impair the natural breathing characteristics of treated substrates, nor will it produce a film. Apply with a roller, brush or sprayer at rate of 100-300 ft² per gallon.

SDI Repel 120 is a premium water repellant with 12% active silane/siloxane for better performance characteristics than Repel 75.

SDI EPO-SHIELD "Satin" is a breathable non-yellowing Water Based penetrating Epoxy-Acylic designed for interior concrete sealing applications such as stamped, stenciled, cementitious overlays, acid stained and brushed or trowel finished concrete surfaces. Use on horizontal and vertical. Meets ASTM cure and seal specifications.

SDI EPO-SHIELD "Gloss" is a non-yellowing Water Based Epoxy-Acrylic designed for interior concrete sealing applications such as stamped, stenciled, cememtitious overlays, acid stained and brushed or trowel finished concrete surfaces. Use on horizontal and vertical. Meets ASTM cure and seal specifications.

SDI 030 is a water based aliphatic urethane topcoat designed to provide excellent abrasion resistance without the typical odors associated with an aliphatic urethane. This product also has an extremely long pot life, and a lighting-fast cure time. At 70 degrees F, the can generally be opened to foot traffic in 3-4 hours. *030 is not recommended for heavy traffic areas*

SDI 357/356PAVOC are single component, moisture-cured aliphatic urethane topcoats. This product has excellent UV stability and wear resistance. 357/356 is comprised of 40% solids, while 357/356PAVOC contains 54% solids. *It is not recommended to use 357/356PAVOC over 015 due to incompatibility issues*

SDI 137M is our best selling 100% solids clear epoxy. 137M exhibits excellent wear characteristics, clarity, ease to use, and UV stability as compared to other clear epoxies on the market.

SDI 139 is a flexible 100% solids clear epoxy designed to be used where flexibility of the coating and potential cracking of the substrate can be an issue. *Use of 139 eliminates the need to repair hairline cracks in the substrate*

SDI 830 Quickset Joint Filler *For use with plural component gun & pump*

SDI 154 is a solvent-based epoxy primer that is cost-effective, high-quality primer for a system where VOC is not an issue.

SDI 707 is one of our best selling products - a 100% solids epoxy topcoat. This product has excellent compressive strength and impact resistance.

Colors Available For Epoxy Flooring

Light Gray	Medium Gray	Dark Gray	Charcoal	Tan	Tile Red
Light Blue	Blue	Green	Brown	Safety Red	Safety Yellow

The Newlook International, Inc. Solid Color Stain is a modified polymer, water-based, high quality concrete color stain, that is made especially for use with existing, unsealed, interior or exterior, concrete surfaces. Solid Color Stain is NOT a paint. It penetrates the surface of porous concrete and forms an opaque, breathable finish that requires no sealer. The solid color stain can be used to restore previously colored surfaces or to rejuvenate old, tired-looking concrete by completely covering discolorations or stains. It can be used on concrete flatwork, vertical surfaces, concrete blocks, pavers, imprinted concrete, exposed aggregate, and many other cementitious surfaces. It can also be used with sandblasting stencils. It is perfect for use over micro-toppings and overlays. The solid color stain comes in a unique 4-part kit that once mixed and applied has an extremely tenacious bond. The large size (32 oz) kit covers approximately 350 square feet (32 square meter) twice. The small size (4 oz.) kit cover approximately 45 square feet (4 square meters) twice. An average of two applications are recommended.

TRANSLUCENT COLOR ENHANCER™ is a semi-transparent (non solid) concrete color stain, designed to be used over the Newlook Solid Color Stain is a contrasting color. The Translucent Color Enhancer is NOT a paint. It is used to tint or enhance areas of relief or texture, stamped concrete surfaces to create an antiqued look. The Enhancer is also used to create a faux finish by blending and layering additional Translucent Color Enhancer colors. It comes in a unique 3-part kit. For additional Translucent Color Enhancer, The Newlook Color Additive (Available in each of the 80 standard Enhancer colors) contains additional pigment and allow customized tinting of the Translucent Color Enhancer Stain. Simply add a color additive to the same color of the Translucent Color Enhancer for more intense concentration of hue. The Large size (16 oz.) kit covers approximately 300-600 square feet (28-56 Square Meters) and a small size (4 oz.) kit covers approximately 75-150 square feet (7-14 Square Meter.)

Sure Hard DP (J-17DP) is a specialized formulation of a reactive water-based siliconate solution. Sure Hard DP (J-17DP) can be used on properly cured new concrete to protect and beautify or on old on concrete to rejuvenate and add life to the floor. Sure Hard DP (J-17DP) penetrates into and reacts with the concrete to harden dustproof and seal concrete and allows for the surface to be highly polished with diamond polishing equipment.